View PIN-1310-2I-LCA_4576680.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PRELIMINARY DATA SHEET
FEATURES:
LC ROSA High performance InGaAs PIN photodiode with separate transimpedance amplifier Low electrical parasitic TO46package Data rates from DC to 4Gbps DC coupled outputs A separate detector bias pin which can be used for receive power monitoring Low bias currents and voltages Automatic gain control for wide dynamic range operation Designed for specifically for video applications Capable of handling 3G SDI pathological test signals
3.7GBS 1310NM PIN+PREAMP ROSA
PIN-1310-2I-LCA
The PIN-1310-2I-LCA is designed specifically for use in video applications and is capable of handling 3G SDI pathological test signals. Consisting of a high-performance InGaAs PIN photo-detector packaged with a transimpedance amplifier designed to meet performance requirements for data rates up to 2.5Gbps data communication over single-mode optical fiber at 1200nm to 1600nm. Other applications include Ethernet, Fiber Channel and ATM protocols.
Part Number
PIN-1310-2I-LCA
Description
1310nm 5 pin LC ROSA, with separate PD bias for RSSI , DC coupled output
PIN-1310-2I-LCA
3.7GBPS 1310NM PIN+PREAMP ROSA
ABSOLUTE MAXIMUM RATINGS
Parameter Storage Temperature Case Operating Temperature Lead Solder Temperature Power Supply Voltage Incident Optical Power ESD exposure level (human body level) Rating -40 to +85C -40 to +85C 260C, 10 sec. -0.5V to 4V +1 dBm average, +4 dBm peak 50V
NOTICE: Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operations section for extended periods of time may affect reliability.
NOTICE: The inherent design of this component causes it to be sensitive to electrostatic discharge (ESD). To prevent ESD-induced damage and/or degradation to equipment, take normal ESD precautions when handling this product.
PIN-1310-2I-LCA
3.7GBPS 1310NM PIN+PREAMP ROSA
ELECTRO-OPTICAL CHARACTERISTICS
3.0VPR =0W, RL=50 AC coupled PR =-12dBm
12 1200 0 50 1300 1.6 42 8
1310
1600
PR,OMA= -12Bm, AC Coupled to RL=50 PR,OMA = -12dBm, AC Coupled to RL=50 PR,OMA =-12dBm
150 2800
400
1,2 1,2 1,2,3
F<3GHz DR = 2.5Gbps PR,OMA =-12dBm, (20%-80%) PR =0W (Dark), 5MHz4 2,5 1,6 7 7
DR = 2.5Gbps PR,OMA =-12dBm, (20%-80%) VR = 0V, Freq = 1MHz VR = 3V, Freq = 1MHz
200 75 40
4 2,5
NOTES
1. 2. PR is the average optical power at the fiber face. PR,OMA is the peak to peak optical power at the fiber face (Optical Modulation Amplitude)
PR ,OMA
3. 4. 5. 6. 7.
2 PR (ER - 1) where ER is the extinction ratio (linear) of the optical source. ER + 1
Bandwidth and Low Frequency Cutoff are measured with a small signal sinusoidal light source with -12dBm average power Sensitivity is measured with an optical source with an extinction ratio of 6dB. Rise/Fall times are corrected for optical source Rise/Fall times. TTIA = TMEASURED - TOPTICAL
2 2 2
Value shown is with no external power supply filtering. The monitor current slope is measured as the current into the PDBIAS connection. PD Offset current is defined as the maximum current measured at VPD with no optical input.
PIN-1310-2I-LCA
3.7GBPS 1310NM PIN+PREAMP ROSA
INTERFACE CONFIGURATION:
VPD VCC 100 VCC VPD VOUTN VOUTP Gnd 50 100nF 50 100
Note: 100 resistor only needed with high impedence limiting amplifiers
12.5x RSSI~1V/mW @ 1310nm
Optional RSSI implementation is shown in blue. Optional 100 differential termination for high impedance limiting amplifiers is shown in red. Recommended bias filter network Note, better performance will be obtained if a ferrite bead is used in place of the inductor.
22uH IN 100uF OUT 100nF
Limiting Amp
100nF
PIN-1310-2I-LCA
3.7GBPS 1310NM PIN+PREAMP ROSA
MOUNTING DIMENSIONS, LC ROSA
for reference only, dimensions in inches
PIN-1310-2I-LCA
3.7GBPS 1310NM PIN+PREAMP ROSA
ADVANCED OPTICAL COMPONENTS
Finisar's ADVANCED OPTICAL COMPONENTS division was formed through strategic acquisition of key optical component suppliers. The company has led the industry in high volume Vertical Cavity Surface Emitting Laser (VCSEL) and associated detector technology since 1996. VCSELs have become the primary laser source for optical data communication, and are rapidly expanding into a wide variety of sensor applications. VCSELs' superior reliability, low drive current, high coupled power, narrow and circularly symmetric beam and versatile packaging options (including arrays) are enabling solutions not possible with other optical technologies. ADVANCED OPTICAL COMPONENTS is also a key supplier of FabreyPerot (FP) and Distributed Feedback (DFB) Lasers, and Optical Isolators (OI) for use in single mode fiber data and telecommunications networks
AOC CAPABILITIES
ADVANCED OPTICAL COMPONENTS' advanced capabilities include: 1, 2, 4, 8, and 10Gbps serial VCSEL solutions 1, 2, 4, 8, and 10Gbps serial SW DETECTOR solutions VCSEL and detector arrays 1, 2, 4, 8, and 10Gbps FP and DFB solutions at 1310 and 1550nm 1, 2, 4, 8, and 10Gbps serial LW DETECTOR solutions Optical Isolators from 1260 to 1600nm range Laser packaging in TO46, TO56, and Optical subassemblies with SC, LC, and MU interfaces for communication networks VCSELs operating at 670nm, 780nm, 980nm, and 1310nm in development Sensor packages include surface mount, various plastics, chip on board, chipscale packages, etc. Custom packaging options
LOCATION
Allen, TX - Business unit headquarters, VCSEL wafer growth, wafer fabrication and TO package assembly. Fremont, CA - Wafer growth and fabrication of 310 to 1550nm FP and DFB lasers. Shanghai, PRC - Optical passives assembly, including optical isolators and splitters.
SALES AND SERVICE
Finisar's ADVANCED OPTICAL COMPONENTS division serves its customers through a worldwide network of sales offices and distributors. For application assistance, current specifications, pricing or name of the nearest Authorized Distributor, contact a nearby sales office or call the number listed below.
Phone: 1-866-MY-VCSEL USA (toll free) 1-972-792-1800 USA (Direct dial) 44 (0) 174 336 5533 Europe 886-935-409898 China & Taiwan 81-90-4437-1130 Japan
Fax: 1-972-238-8670 USA 44 (0) 979 445 2047 Europe 03 5440-1368 Asia Email: support@adopco.com WEB: www.finisar.com/aoc.php
(c)2007 Finisar Corporation. All rights reserved. Finisar is a registered trademark of Finisar Corporation. Features and specifications are subject to change without notice. 02/09 Rev D.

▲Up To Search▲

Price & Availability of PIN-1310-2I-LCA

	To Download PIN-1310-2I-LCA Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .